SV-JME is indexed / abstracted in:

  • SCI-Expanded,
  • Compendex,
  • Inspec,
  • ProQuest-CSA,
  • SCOPUS,
  • TEMA, ...
The list of the remaining bases, in which SV-JME is indexed »

Founders and Publishers

University of Ljubljana, Faculty of Mechanical Engineering

University of Maribor, Faculty of Mechanical Engineering

 

Association of Mechanical Engineers of Slovenia

 

Chamber of Commerce and Industry Slovenia, Metal Processing Association

Editorial Office

University of Ljubljana
Faculty of Mechanical Engineering
Journal of Mechanical Engineering
Aškerčeva 6,

SI-1000 Ljubljana
Slovenia

P: +386 1 4771 137
E: info@sv-jme.eu


The magazine is subsidized by the Slovenian Book Agency (JAK).

 

Journal of Mechanical Engineering - Volume 2011

   

SV - JME 57 (2011) 12

Table of contents

  1. Pipistrel Taurus G4: on Creation and Evolution of the Winning Aeroplane of NASA Green Flight Challenge 2011
  2. Kinematics and Dynamics of the Quasi-Passive Biped “PASIBOT”
  3. Finite Element Analysis of a Tire Steady Rolling on the Drum and Comparison with Experiment
  4. Influence of the Milling Strategy on the Durability of Forging Tools
  5. Polycrystalline Cubic Boron Nitride (PCBN) Tool Life and Wear in Turning of Amorphous-Crystalline Iron-Based Coatings
  6. Simulation of Water-Gas Shift Membrane Reactor for IGCC Plant with CO2 Capture
  7. Characteristics of Surface Treated Nuclear Grade Stainless Steel Type AISI 316 LN at 25 to 500 °C
  8. Experimental Equipment Research for Cryogenic Joule-Thompson Cryocoolers Comparison in IR Technology Sensors

To journal contents >>
   

SV - JME 57 (2011) 11

Table of contents

  1. CW Fiber Laser for Second Harmonic Generation
  2. Structural Analysis of an Articulated Urban Bus Chassis via FEM: a Methodology Applied to a Case Study
  3. Calculation of the Combined Torsional Mesh Stiffness of Spur Gears with Two- and Three-Dimensional Parametrical FE Models
  4. Implementation of Automatic Identification Technology in a Process of Fixture Assembly/Disassembly
  5. Possibilities of Using Three-Dimensional Optical Scanning in Complex Geometrical Inspection
  6. Effects of Hot-Water-Pipeline Renovation in a District Heating System
  7. On the Particles Size Distributions of Diatomaceous Earth and Perlite Granulations
  8. Quality Managers’ Estimates of Quality Management Principles Application in Certified Organisations in Transitional Conditions - Is Serbia Close to TQM?

To journal contents >>
   

SV - JME 57 (2011) 10

Table of contents

  1. Development of a Part-Complexity Evaluation Model for Application in Additive Fabrication Technologies
  2. Overall Structure Calibration of 3-UCR Parallel Manipulator Based on Quaternion Method
  3. Optimal Control of Workpiece Thermal State in Creep-Feed Grinding Using Inverse Heat Conduction Analysis
  4. The Formation of Saw Toothed Chip in a Titanium Alloy: Influence of Constitutive Models
  5. The Influence of Airflow Inlet Region Modifications on the Local Efficiency of Natural Draft Cooling Tower Operation
  6. Global Optimization of Lateral Performance for Two-Post ROPS Based on the Kriging Model and Genetic Algorithm
  7. Development of Prosthetic Knee for Alpine Skiing
  8. Application of Promethee-Gaia Methodology in the Choice of Systems for Drying Paltry-Seeds and Powder Materials

To journal contents >>
   

SV - JME 57 (2011) 9

Table of contents

  1. Sustainability Assessment: Cryogenic Machining of Inconel 718
  2. Length Variation of Toothed Belt during Exploitation
  3. Signal Model-Based Fault Detection and Diagnosis for Induction Motors Using Features of Vibration Signal in Two-Dimension Domain
  4. FE-Modeling of Cold Rolling by In-Feed Method of Circular Grooves
  5. Surface Topography Modelling for Reduced Friction
  6. Aspects of Using Tool Axis Inclination Angle
  7. Influence of Input Parameters on the Characteristics of the EDM Process
  8. Application of Numerical Simulations in the Deep-Drawing Process and the Holding System with Segments’ Inserts

To journal contents >>
   

SV - JME 57 (2011) 7-8

Table of contents

  1. Simulating Nonlinear Materials under Centrifugal Forces by using Intelligent Cross-linked Simulations
  2. Validation of a Flexible Multibody Belt-Drive Model
  3. Integrated Design for Fatigue Life Estimation of Structures
  4. Mesh Smoothing with Global Optimization under Constraints
  5. Study of Adaptive Model Parameter Estimation for Milling Tool Wear
  6. Numerical Modelling of Crack Growth in a Gear Tooth Root
  7. Design and Testing of an Ultrasound System for Targeted Spraying in Orchards
  8. Integrating R&D and Marketing in New Product Development
  9. Virtual Engine - A Tool for a Powertrain Dynamic Solution
  10. Computation of Stress Intensity Factor in Functionally Graded Plates under Thermal Shock

To journal contents >>
   

SV - JME 57 (2011) 6

Table of contents

  1. Numerical Prediction of Non-Cavitating and Cavitating Vortex Rope in a Francis Turbine Draft Tube
  2. A Methodology for Quantifying the Kinematic Position Errors due to Manufacturing and Assembly Tolerances
  3. A Secondary Source Configuration for Control of a Ventilation Fan Noise in Ducts
  4. Fault Detection of an Industrial Heat-Exchanger: A Model-Based Approach
  5. Numerical Methods for TMF Cycle Modeling
  6. Criticality Analysis of the Elements of the Light Commercial Vehicle Steering Tie-Rod Joint
  7. Mathematical Model of an Autoclave
  8. Theoretical Analysis of Stiffness Constant and Effective Mass for a Round-Folded Beam in MEMS Accelerometer

To journal contents >>
   

SV - JME 57 (2011) 5

Table of contents

  1. Creep Damage Calculation for Thermo Mechanical Fatigue
  2. Surface Integrity of Shot Peened Aluminium Alloy 7075-T651
  3. Surface Modification of Aluminium Alloys with Laser Shock Processing
  4. An Intelligent Electro-Hydraulic Servo Drive Positioning
  5. Determining the Capacity of Unloading Bulk Cargo Terminal Using Queuing Theory
  6. Investigation of TiN Coated CBN and CBN Cutting Tool Performance in Hard Milling Application
  7. Conservative-Force-Controlled Feed Drive System for Down Milling

To journal contents >>
   

SV - JME 57 (2011) 4

Table of contents

  1. Modeling Techniques of Nested Helical Structure Based Geometry for Numerical Analysis
  2. Melt Volume Flow Measurement in the Mineral-Wool Production Process
  3. Optimization of Trapezoidal Cross Section of the Truck Crane Boom by Lagrange’s Multipliers and by Differential Evolution Algorithm (DE)
  4. Position Control with Parameter Adaptation for a Nano-Robotic Cell
  5. A Study of Quality Parameters and Behaviour of Self-Piercing Riveted Aluminium Sheets with Different Joining Conditions
  6. Surface Integrity after Mechanical Hardening of Various Aluminium Alloys
  7. Fatigue Failure Study of the Lower Suspension Vehicle Arm Using a Multiaxial Criterion of the Strain Energy Density
  8. Taguchi-Based and Intelligent Optimisation of a Multi-Response Process Using Historical Data

To journal contents >>
   

SV - JME 57 (2011) 3

Table of contents

  1. New Opportunities for NDT Using Non-Linear Interaction of Elastic Waves with Defects
  2. Lockin-Interferometry: Principle and Applications in NDE
  3. Application of Ultrasonic C-Scan Techniques for Tracing Defects in Laminated Composite Materials
  4. Electromagnetic Nondestructive Evaluation: Present and Future
  5. NDT Based Process Monitoring and Control
  6. Electromagnetic Imaging Using Probe Arrays
  7. Study of Weak Electric Current Emissions on Cement Mortar under Uniaxial Compressional Mechanical Stress up to the Vicinity of Fracture
  8. Focus Variation – a Robust Technology for High Resolution Optical 3D Surface Metrology
  9. Surface Defect Detection on Power Transmission Belts Using Laser Profilometry
  10. Monitoring Gas Metal Arc Welding Process by Using Audible Sound Signal

To journal contents >>
   

SV - JME 57 (2011) 2

Table of contents

  1. Energy Saving Cooling-Unit for Plastic Moulding Machine
  2. The Influence of Chip Breaker Geometry on Tool Stresses in Turning
  3. System Approach to Vehicle Suspension System Control in CAE Environment
  4. Application of Genetic Algorithm into Multicriteria Batch Manufacturing Scheduling
  5. Energy Savings in Building with a PCM Free Cooling System
  6. FPGA-Based Control System of an Ultrasonic Phased Array
  7. Real-Time Cutting Tool Condition Monitoring in Milling
  8. Improvement of Business Processes Performances through Establishment of the Analogy: Quality Management System – Human Organism

To journal contents >>
   

SV - JME 57 (2011) 1

Table of contents

  1. Rotating-Mirror Q-Switched Er:YAG Laser for Optodynamic Studies
  2. The Effect of Electroless Ni Coating of SiC Particles on the Corrosion Behavior of A356 Based Squeeze Cast Composite
  3. Measuring Dynamic Loads on a Foldable City Bicycle
  4. Interrelation between ERP Modification and Modification Scheduling: Four SME Case Studies in Croatia
  5. Fatigue Life Analysis of Aluminum Wheels by Simulation of Rotary Fatigue Test
  6. Comparison between Elastic-Perfectly-Plastic Interfacial Free-Edge and Crack Tip Singular Fields
  7. Shaping of Face Toothing in Flat Spiroid Gears
  8. Analysis of Company Development Factors in Manufacturing and Service Company: a Strategic Approach
  9. Nonlinear Approach to Thin-Walled Beams with a Symmetrical Open Section

To journal contents >>
   


Sign up for the FREE SV-JME Newsletter

Enter your email address below to receive your newsletter subscriptions.
Name and surname:

E-mail:
Subscribe
Unsubscribe